Arama Sonuçları..
Toplam 58 kayıt bulundu.
BITE BUMPER™
Bite Bumpers™ work to open deep bite cases by allowing the anteriors to ride up and out of occlusion. The Bite Bumpers™ eliminate bond failures of brackets and are especially valuable with ceramic or self-ligating brackets.The unique fixed "placement-jig" guarantees the correct height on the lingual of the tooth an makes sure the two Bite Bumpers™ are 100% parallel.The Bite Bumpers™ are made of a composite polymer that is more comfortable, aesthetic and will increase biocompatibility in nickel sensitive patients.Bite-Bumpers™ are bonded in the same manner as plastic or composite brackets with a slotted mechanical bonding base.Bite Bumper is a registered trademark by Gestenco International AB, Sweden
http://www.eksenmedikal.com.tr/bite-bumper
M5™ Copper Nickel Titanium - Trueform™ II
Trueform™ II A premium nickel titanium wire that incorporates a precise temperature transformation at 27°C for predictable tooth moving forces. G&H quality manufacturing and testing processes make M5™ Copper Nickel Titanium distinct from all other archwires used in orthodontics.Many orthodontists induce the martensitic phase by chilling the wire below its transition temperature prior to placement. Following engagement, as the thermal wire elevates in temperature within the oral cavity, the transition from martensitic to austenitic phases causes the force level to increase and the shape memory phenomenon to occur.
http://www.eksenmedikal.com.tr/m5-copper-nickel-titanium-trueform-ii
SmartBond® Adhesive
SmartBond® Cyanoacrylate AdhesiveSmartBond® is a true one-step adhesive that bonds in a wet field. In fact,it is activated only when it contacts moisture.Teeth are cleaned and etched for bonding as usual, but when the etchant is rinsed off, the next step is to bond. There is no drying, no sealants and there is no dry field to maintain.SmartBond® activation begins when a bondable attachment is delivered to the tooth and the adhesive contacts wet enamel. Five-second working time, five minute bond set.SmartBond® makes bonding in difficult locations easy. Partially or surgically exposed teeth, molars, lingually displaced teeth and high cuspids all can be successfully bonded with SmartBond®.SmartBond® is a filled cyanoacrylate base adhesive. Care should be taken in dispensing, use and storage to avoid unintended adhesion. Refigeration of SmartBond® is recommended.SmartBond® is a registerd trademark of Gestenco International AB, Sweden
http://www.eksenmedikal.com.tr/smartbond-adhesive
G&H Stainless Steel - KOBAYASHI TIES
G&H® Koby Ties provide an auxiliary hook which can be added to any bracket just by tying in the archwire. Preformed to be easily tied in place and able to fit most orthodontic brackets. Made from easily adaptable .012 or .014 ligature wire. Available in Short, Long or Tooth-Colored.
http://www.eksenmedikal.com.tr/stainless-steel-kobayashi-ties
G&H Stainless Steel - LIGATURE TIES
Our Short and Long stainless steel ligature ties are prefomed in dead soft temper. Also available in Tooth-Colored.
http://www.eksenmedikal.com.tr/g-h-stainless-steel-ligature-ties
G&H BOND-A-BRAID™ LINGUAL RETAINER 10PK
Permanent retention is greatly enhanced using a flattened, dead soft 8-braided wire. Intra-arch splinting with this thin ribbon arch prevents torque control problems that can occur using a round braided wire for these procedures.When bonded on the lingual of the upper incisors, a very thin rectangular wire can be adapted with little lower incisor interference.The dead soft wire is easy to adapt and prevents inadvertent tooth movement associated with active force wires.Bond-A-Braid is excellent for semi-permanent orthodontic splinting of the upper or lower incisors. It can be used to hold diastemas closed, maintain difficult extraction sites and solving various other tooth-splinting dilemmas.Excellent for splinting periodontally comprised teeth.(10) 6" lengths
http://www.eksenmedikal.com.tr/bond-a-braid-lingual-retainer-10pk
GAC Open Coil Spring
Open, or compression, coils are 15mm in length when passive and may be compressed to 3mm. Between these points, the coil will exert 50 (extra light), 100 (light), 150 (medium), 200 (heavy), or 250 (extra heavy) , and 300 (XX Heavy) grams of force until 14mm, and then the force falls to 0 as it becomes passive again. No distortion will occur during movement. These low forces limit patient discomfort and ensure good circulation in the periodontal pocket during movement. Typically, you will see 4mm of space opened in three months (this varies depending on the age and health of the patient). To engage the open coils, mark the archwire where the mesial and distal tooth destinations are located. Crimp on the mesial stop and ligate the archwire up to the point where the spring is to be placed. Slide the coil over the archwire and crimp on the distal stops. Ligate the balance of the wire. Since the Sentalloy coil needs about 1/10 as much wire as steel, good hygiene is much easier, but do advise the patient to rinse and brush around the coil. No other adjustment is needed.
http://www.eksenmedikal.com.tr/open-coil-spring
GAC Sentalloy® Closed Coil Springs
Closing spaces with closed Sentalloy coil springs brings exceptional results. TWO DESIGNS ARE AVAILABLE: Two Eyelet Design: The initial length is 3mm unactivated (this does not include the eyelet lengths). These can be activated to 15mm without any deformation or change in force. No change in force will be seen as the coil contracts, reducing the space. To engage, slide over a molar hook and slowly stretch to the post on the cuspid bracket or a sliding hook on the archwire. Use a locking Mathieu plier on the widened platform of the eyelet. If you do not use the cuspid post, tie the archwire to the tooth you wish to move, slide on the sliding hook, then tie in the balance of the wire. Now engage the spring as above. For an eyelet with ligature wire, you have the option of hooking the eyelet on the molar, then activating the spring and tying it to the cuspid bracket with the .008” ligature wire. Should you wish to span an area greater than 15mm, measure the span first. Then place the coil on the molar hook and activate the coil 10mm. Tie the ligature wire to the bracket.
http://www.eksenmedikal.com.tr/gac-sentalloy-closed-coil-springs